[driverloader] Re: Can not get WUSB64G working!!

[Linuxant support (Jonathan)]

Hi,

in the first email you have sent to the list, we can see that you are 
not associated (connected) to the access point because we can't see the 
MAC address of an access point in the output of the 'iwconfig' command 
while the wireless interface is configured.

You could try to disable WEP to see if this is the source of the 
problem. You could also try with different versions of the Windows XP 
driver.

Finally, you could try with a kernel compiled without the CONFIG_PREEMPT 
option. We have greatly improved support for the PREEMPT option in 
DriverLoader 2.28 but it's still not perfect.

Regards,


Jonathan
Technical specialist / Linuxant
www.linuxant.com
support at linuxant.com



Joe LeBlanc wrote:
> Some more info from the diag tool
> 
> 
> 
> Joe LeBlanc wrote:
> 
> 
>>I have the Linksys Wireless-G USB Network Adapter ( WUSB54G ) and im
>>trying to get this installed on Gentoo, Here is some information I
>>gotten for review:
>>
>>$ dmesg
>>usb 2-1: new full speed USB device using ohci_hcd and address 19
>>driverloader: stack=8192/60/0 PREEMPT
>>driverloader: wusb20xp.sys: 0xe0cdc000..0xe0d2e520 entry = e0cf7ebf
>>(pbase = 0x10000)
>>eth2: WPA, AES, TKIP, WEP128, WEP64 supported
>>eth2: Linksys Wireless-G USB Network Adapter at 0000:00:02.11 (MAC
>>address 00:0F:66:16:BD:A8) ready
>>eth2: New link status: Disconnected (0002)
>>usbcore: registered new driver driverloader
>>
>>$ iwconfig eth2
>>eth2      IEEE 802.11g  ESSID:""  Nickname:"unknown"
>>         Mode:Managed  Bit Rate=2 Mb/s  
>>         RTS thr:off   Fragment thr:off
>>         Encryption key:off
>>         Power Management:off
>>         Link Quality:0  Signal level:0  Noise level:0
>>         Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
>>         Tx excessive retries:0  Invalid misc:0   Missed beacon:0
>>
>>$ iwconfig eth2 key open xxxxxxxxxxxxxxxxxxxxxxxxxx
>>$ iwconfig eth2 essid xxxxxxxx
>>$ ifconfig eth2 inet 192.168.0.252 netmask 255.255.255.0 broadcast
>>192.168.0.255
>>
>>$ iwconfig eth2
>>eth2      IEEE 802.11g  ESSID:"xxxxxxxx"  Nickname:"unknown"
>>         Mode:Managed  Bit Rate=2 Mb/s  
>>         RTS thr:off   Fragment thr:off
>>         Encryption key:xxxx-xxxx-xxxx-xxxx-xxxx-xxxx-xx   Security
>>mode:open
>>         Power Management:off
>>         Link Quality:0  Signal level:0  Noise level:0
>>         Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
>>         Tx excessive retries:0  Invalid misc:0   Missed beacon:0
>>
>>$ ifconfig eth2
>>eth2   Link encap:Ethernet  HWaddr 00:0F:66:16:BD:A8 
>>         inet addr:192.168.0.252  Bcast:192.168.0.255  Mask:255.255.255.0
>>         UP BROADCAST MULTICAST  MTU:1500  Metric:1
>>         RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>         TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>         collisions:0 txqueuelen:1000
>>         RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
>>
>>$ ping -I eth2 192.168.0.1
>>PING 192.168.0.1 (192.168.0.1) from 192.168.0.252 eth2: 56(84) bytes of
>>data.
> 
>>From 192.168.0.252 icmp_seq=1 Destination Host Unreachable
>>From 192.168.0.252 icmp_seq=2 Destination Host Unreachable
>>From 192.168.0.252 icmp_seq=3 Destination Host Unreachable
>>From 192.168.0.252 icmp_seq=5 Destination Host Unreachable
>>From 192.168.0.252 icmp_seq=6 Destination Host Unreachable
>>From 192.168.0.252 icmp_seq=7 Destination Host Unreachable
> 
>>--- 192.168.0.1 ping statistics ---
>>7 packets transmitted, 0 received, +6 errors, 100% packet loss, time 6014ms
>>
>>
>>
>> 
>>
> 
> 
> _______________________________________________
> driverloader mailing list
> driverloader at lists.linuxant.com
> https://www.linuxant.com/mailman/listinfo/driverloader