[driverloader] Problem with DWL-G132
Phil W
philw_1971 at hotmail.com
Sun Feb 19 08:46:13 EST 2006
Hi,
I am having problems getting the above adapter to work under Suse 10.0 (open
source). I have installed the Linuxant driver without any apparent errors. I
then go to the configurator web page and load the athfmwdl.inf file. I then
load ar5523.bin and athfmwdl.sys, at which point I get:
"No devices found. - It seems that your device is either not present or not
supported by the installed driver(s)."
I have a dual boot box and the adapter works fine under Windows.
I have seen lots of reference to the following (in this case, the known
issues on the Linuxant website: "Atheros USB adapters require loading of
both the firmware driver (athfmwdl) and the network driver (typically
neta5agu).". However I can't find any instructions on how to load this - I
have the file neta5agu.cat on my disk/system, but no inf file.
Any help would be most appreciated. I paste some diagnostics below:
Thanks in advance,
Phil
Linux version 2.6.13-15-smp (geeko at buildhost) (gcc version 4.0.2 20050901
(prerelease) (SUSE Linux)) #1 SMP Tue Sep 13 14:56:15 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e400 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
BIOS-e820: 000000007fff0000 - 000000007fff3000 (ACPI NVS)
BIOS-e820: 000000007fff3000 - 0000000080000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
1151MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f50c0
On node 0 totalpages: 524272
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 294896 pages, LIFO batch:31
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 GBT ) @ 0x000f6ba0
ACPI: RSDT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x7fff3000
ACPI: FADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x7fff3040
ACPI: MADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x7fff6f40
ACPI: DSDT (v001 GBT AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:3 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:3 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 80000000:7ec00000)
Built 1 zonelists
Kernel command line: root=/dev/sda5 vga=0x317 selinux=0 resume=/dev/sdb6
splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 3216.105 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2071932k/2097088k available (2330k kernel code, 23864k reserved,
750k data, 252k init, 1179584k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 6437.49 BogoMIPS
(lpj=12874998)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
0000441d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
0000441d 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 0000441d
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 1768k freed
ACPI: Looking for DSDT in initrd... not found!
not found!
CPU0: Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 04
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6431.38 BogoMIPS
(lpj=12862772)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
0000441d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
0000441d 00000000 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 0000441d
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 04
Total of 2 processors activated (12868.88 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb230, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
TC classifier action (bugs to netdev at vger.kernel.org cc hadi at cyberus.ca)
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f6000000-f8ffffff
PREFETCH window: e8000000-efffffff
PCI: Bridge: 0000:00:1e.0
IO window: 9000-9fff
MEM window: f4000000-f5ffffff
PREFETCH window: f0000000-f3ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1140337253.684:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
vesafb: framebuffer at 0xe8000000, mapped to 0xf8880000, using 6144k, total
131072k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:d0e0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 76011
bytes,<6>...found (1024x768, 12703 bytes, v3).
Console: switching to colour frame buffer device 127x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
input: PC Speaker
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 7, 524288 bytes)
TCP established hash table entries: 524288 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI wakeup devices:
PCI0 HUB0 USB0 USB1 USB2 USB3 USBE
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 252k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
ICH5: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GSA-4081B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Adaptec aacraid driver (1.1-4 Sep 13 2005 17:29:46)
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 16 (level, low) -> IRQ 177
AAC0: kernel 4.2-0[7348]
AAC0: monitor 4.2-0[7348]
AAC0: bios 4.2-0[7348]
AAC0: serial bba330
scsi0 : aacraid
Vendor: ADAPTEC Model: Operating_Syste Rev: V1.0
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 29356032 512-byte hdwr sectors (15030 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: got wrong page
sda: assuming drive cache: write through
SCSI device sda: 29356032 512-byte hdwr sectors (15030 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: got wrong page
sda: assuming drive cache: write through
sda: sda1 sda2 < sda5 >
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Vendor: ADAPTEC Model: User_data Rev: V1.0
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 1435478016 512-byte hdwr sectors (734965 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
sdb: got wrong page
sdb: assuming drive cache: write through
SCSI device sdb: 1435478016 512-byte hdwr sectors (734965 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: got wrong page
sdb: assuming drive cache: write through
sdb: sdb1 < sdb5 sdb6 sdb7 sdb8 >
Attached scsi removable disk sdb at scsi0, channel 0, id 1, lun 0
Attached scsi generic sg1 at scsi0, channel 0, id 1, lun 0, type 0
ACPI: CPU0 (power states: C1[C1])
ACPI: CPU1 (power states: C1[C1])
scsi_id[1310]: 0:0:1:0: page 0 not available.
scsi_id[1312]: 0:0:1:0: page 0 not available.
ACPI: Thermal Zone [THRM] (22 C)
ACPI: Fan [FAN] (on)
Attempting manual resume
swsusp: Suspend partition has wrong signature?
ReiserFS: sda5: found reiserfs format "3.6" with standard journal
ReiserFS: sda5: using ordered data mode
ReiserFS: sda5: journal params: device sda5, size 8192, journal first block
18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda5: checking transaction log (sda5)
ReiserFS: sda5: Using r5 hash to sort names
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Adding 1052216k swap on /dev/sdb6. Priority:-1 extents:1
bootsplash: status on console 0 changed to on
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel at redhat.com
NTFS driver 2.1.23 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS volume version 3.1.
ReiserFS: sdb8: found reiserfs format "3.6" with standard journal
ReiserFS: sdb8: using ordered data mode
ReiserFS: sdb8: journal params: device sdb8, size 8192, journal first block
18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sdb8: checking transaction log (sdb8)
ReiserFS: sdb8: Using r5 hash to sort names
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ndiswrapper: module not supported by Novell, setting U taint flag.
ndiswrapper version 1.2 loaded (preempt=no,smp=yes)
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 177, io base 0x0000ac00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 185, io base 0x0000a000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 169, io base 0x0000a400
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 177, io base 0x0000a800
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 193, io mem 0xf9000000
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel i875 Chipset.
agpgart: AGP aperture is 128M @ 0xe0000000
hw_random: RNG not detected
e100: Intel(R) PRO/100 Network Driver, 3.4.8-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 20 (level, low) -> IRQ 201
e100: eth0: e100_probe: addr 0xf5008000, irq 201, MAC addr 00:0D:61:66:02:01
usb 5-2: new high speed USB device using ehci_hcd and address 2
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1299 $ Ben Collins <bcollins at debian.org>
ACPI: PCI Interrupt 0000:02:01.2[B] -> GSI 22 (level, low) -> IRQ 209
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[209] MMIO=[f500a000-f500a7ff]
Max Packet=[2048]
ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 209
ohci1394: fw-host1: OHCI-1394 1.1 (PCI): IRQ=[209] MMIO=[f5009000-f50097ff]
Max Packet=[2048]
gameport: EMU10K1 is pci0000:02:01.1/gameport0, io 0x9400, speed 1125kHz
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 21 (level, low) -> IRQ 217
ALSA sound/pci/emu10k1/emufx.c:1385: Installing spdif_bug patch: Audigy 2 ZS
[SB0350]
hda: ATAPI 32X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
bootsplash: status on console 0 changed to on
usb 3-1: new low speed USB device using uhci_hcd and address 2
usb 3-2: new full speed USB device using uhci_hcd and address 3
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c01510ee613]
usbcore: registered new driver hiddev
input: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on
usb-0000:00:1d.2-1
input: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on
usb-0000:00:1d.2-1
input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.2-2
input,hiddev96: USB HID v1.11 Device [Logitech USB Receiver] on
usb-0000:00:1d.2-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
driverloader: no version for "struct_module" found: kernel tainted.
driverloader: module license 'see LICENSE file; Copyright (c)2003-2004
Linuxant inc.' taints kernel.
ieee1394: Host added: ID:BUS[1-00:1023] GUID[000d6100005f7ff8]
driverloader: stack=8192/60/0 REGPARM SMP
usbcore: registered new driver driverloader
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NET: Registered protocol family 17
nvidia: module not supported by Novell, setting U taint flag.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 177
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7676 Fri Jul 29
12:58:54 PDT 2005
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
bootsplash: status on console 0 changed to on
IA-32 Microcode Update Driver: v1.14 <tigran at veritas.com>
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03ba0a0(lo)
IPv6 over IPv4 tunneling driver
microcode: CPU0 not 'upgrading' to earlier revision 0x13 (current=0x17)
microcode: CPU1 not 'upgrading' to earlier revision 0x13 (current=0x17)
microcode: No new microcode data for CPU1
microcode: No new microcode data for CPU0
IA-32 Microcode Update Driver v1.14 unregistered
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
powernow: This module only works with AMD K7 CPUs
bootsplash: status on console 0 changed to on
subfs 0.9
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
subfs: unsuccessful attempt to mount media (256)
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
eth0: no IPv6 routers present
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
subfs: unsuccessful attempt to mount media (256)
usbcore: deregistering driver driverloader
driverloader: stack=8192/60/0 REGPARM SMP
usbcore: registered new driver driverloader
usbcore: deregistering driver driverloader
driverloader: stack=8192/60/0 REGPARM SMP
usbcore: registered new driver driverloader
More information about the driverloader
mailing list