[driverloader] Allnet 0281 WPA config

[Joerg Bingemer]

Hi,

I just downloaded the trial version of the driver loader. I installed 
the trial and added the driver for the card over the web setup.

This looks for me like everything went well:

driverloader: stack=8192/60/0
usbcore: registered new driver driverloader
driverloader: alnetg.sys: 0xd0d4a000..0xd0d9e200 entry = d0d70130 (pbase 
= 0x10000)
ACPI: PCI Interrupt 0000:03:09.0[A] -> GSI 21 (level, low) -> IRQ 209
eth1: New link status: Disconnected (0002)
eth1: WPA, AES, TKIP, WEP128, WEP64 supported
eth1: at 0000:03:09.0 (MAC address 00:0F:A3:1B:14:33) ready

Has someone good tipps with examples ? Here is my wpa_supplicant output:

wpa_supplicant -i eth1 -c /etc/wpa_supplicant.conf -dd
Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 
'default'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group=0
eapol_version=1
ap_scan=1
fast_reauth=1
Line: 264 - start of a new network block
ssid - hexdump_ascii(len=23):
     46 52 49 54 5a 21 42 6f 78 20 46 6f 6e 20 57 4c   FRITZ!Box Fon WL
     41 4e 20 37 31 37 30                              AN 7170
proto: 0x2
key_mgmt: 0x2
pairwise: 0x10
group: 0x10
PSK (ASCII passphrase) - hexdump_ascii(len=16): [REMOVED]
priority=5 (0x5)
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 5
   id=0 ssid='FRITZ!Box Fon WLAN 7170'
Initializing interface (2) 'eth1'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Own MAC address: 00:0f:a3:1b:14:33
wpa_driver_hostap_set_wpa: enabled=1
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_countermeasures: enabled=0
wpa_driver_hostap_set_drop_unencrypted: enabled=1
Setting scan request: 0 sec 100000 usec
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
Starting AP scan (broadcast SSID)
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Wireless event: cmd=0x8b19 len=8
Received 273 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 5
0: 00:15:0c:cd:59:8a ssid='' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
No suitable AP found.
Setting scan request: 5 sec 0 usec
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Signal 2 received - terminating

I want to connect to a FritzBox 7170 Wlan (I don't know which WPA 
Version is used, I think WPA2)

Best Regards
Joerg