Fwd: [hcflinux] framing error - EC_ERROR: Frame xx is out of order.

[scytale]

>
>>Apologies if this message appears twice, or even three times - it kept 
>>getting bounced back because I was using the wrong email address.
>
>
>>I noticed the thread from last week regarding the above error message.
>>I have been having a similar problem.
>>I am using the  conextant HCF winmodem
>>The modem works just fine with a ppp link to my isp, but the driver keeps 
>>routing messages relating to messed up frames to the console.When there 
>>is a download of any size going on the screen rapidly becomes covered in 
>>gunk. The phone line here is noisy - I get reported connection speeds of 
>>16Kb/s under windows.
>>
>>Example - from /var/log/debug :
>>
>>Apr 18 12:35:53 jupiter kernel: 1222504.288: >>>EC_ERROR: Frame 69 is out 
>>of order. (68)1222504.288: >>>EC_ERROR: build_rej_p0
>>
>>Marc said to send him the capture from AT#UG so it is at the bottom of 
>>this mail.
>>
>>I want to get the damn thing off my console  - switching to gui cures it 
>>but that's not the point.
>>
>>How Can I stop the messages from going to the console?
>
>Is there any way to change the debug output of the driver?
>
>
>>I am using syslog-ng and the killer is I can't see in the .conf file 
>>anywhere that could be telling it to send this crap straight to the console.
>>There was only one line in syslog-ng.conf concerning  logging to console 
>>(for emergencies) and I disabled that earlier on (line 2 of this extract) :
>> >syslog-ng.conf extract<
>>
>>log { source(src); filter(f_messages); destination(messages); };
>>#log { source(src); filter(f_emergency); destination(console); };
>>log { source(src); filter(f_cnews); destination(xconsole); };
>>log { source(src); filter(f_cother); destination(xconsole); };
>>
>> >end extract<
>>
>>Any ideas relating to syslog-ng or to the modem driver?
>>There is no mention of turning off/on debugging in the modem driver docs.
>
>
>System
>
>>Debian 2.2r5
>>kernel 2.2.16
>>pppd 2.4.? - yeah I updated it
>>syslog 2.5.16 - update from 2.4.0 earlier on to no avail
>>hcflinmodem package 0.9beta02041300
>>
>>Thanks
>>tom
>>
>>MINICOM CAPTURE
>>----------------------------------------------------------------------------------------------------------------------------
>>
>>#ug
>><#UG VERSION=1>
>><UNIMODEM VERSION=10>
>><CALL SETUP RESULT=Detected Data Answer Tone>
>><MULTIMEDIA MODE=Data Only>
>><DTE-DCE MODE=Async data>
>><V.8 CM octet string="">
>><V.8 JM octet string="">
>><RX SIG POWER DB=26, TX SIG POWER DB=15, S/N RATIO DB=18>
>><NORMALIZED MEAN SQUARED ERROR=0>
>><NEAR ECHO LOSS=0>
>><FAR ECHO LOSS=0>
>><FAR ECHO DELAY=0>
>><ROUND TRIP DELAY=0>
>><V.34 INFO bit map =0>
>><TX MOD=V.34, TX SYMBOL RATE=3429, TX CARRIER FREQ=0>
>><RX MOD=V.34, RX SYMBOL RATE=3429, RX CARRIER FREQ=0>
>><TX FIRST DATA RATE=14400, RX FIRST DATA RATE=14400>
>><CARRIER LOSS=0, RATE RENEG=0>
>><RETRAINS REQ=1, RETRAINS DET=0>
>><TX FINAL RATE=14400, RX FINAL RATE=14400>
>><PROTOCOL NEGOTIATION=LAPM>
>><EC FRAME SIZE=80>
>><EC LINK TIMEOUTS=0>
>><EC LINK NAKS=0>
>><COMPRESSION NEGOTIATION=V42BIS>
>><COMPRESSION DICTIONARY SIZE=800>
>><TX FLOW CONTROL=2>
>><RX FLOW CONTROL=2>
>><TX CHARS SENT FROM DTE=261E>
>><RX CHARS SENT TO DTE=16600>
>><TX CHARS LOST=0>
>><RX CHARS LOST=0>
>><TX FRAME COUNT=9F>
>><RX FRAME COUNT=33D>
>><TX FRAME ERROR COUNT=D>
>><RX FRAME ERROR COUNT=12>
>><TERMINATION CAUSE=Retrain failed>
>><LSD Vdd=0, Power Bits=0>
>><V8BIS FLEX VERSION=0, V8BIS DSP VERSION=47>
>><RATE RENEG REQ=0, RATE RENEG DET=0>
>><HIGH PASS FILTER ENABLED=0>
>><ROBBED BIT PATTERN=0>
>><DIGITAL PAD DETECTED=0, DIGITAL LOSS ESTIMATE=0>
>><Cnt1=0, Det1=1, Res1=0>
>><EQM=7FF7, TRAINING EQM SUM=48FF0>
>><DIB ERROR COUNTERS=0, 0, 0, 0, 0, 0, 0, 0>
>><RETRAIN/HDLC RESET=0>
>>
>>OK
>>at#ug
>><#UG VERSION=1>
>><UNIMODEM VERSION=10>
>><CALL SETUP RESULT=Detected Data Answer Tone>
>><MULTIMEDIA MODE=Data Only>
>><DTE-DCE MODE=Async data>
>><V.8 CM octet string="">
>><V.8 JM octet string="">
>><RX SIG POWER DB=26, TX SIG POWER DB=15, S/N RATIO DB=18>
>><NORMALIZED MEAN SQUARED ERROR=0>
>><NEAR ECHO LOSS=0>
>><FAR ECHO LOSS=0>
>><FAR ECHO DELAY=0>
>><ROUND TRIP DELAY=0>
>><V.34 INFO bit map =0>
>><TX MOD=V.34, TX SYMBOL RATE=3429, TX CARRIER FREQ=0>
>><RX MOD=V.34, RX SYMBOL RATE=3429, RX CARRIER FREQ=0>
>><TX FIRST DATA RATE=14400, RX FIRST DATA RATE=14400>
>><CARRIER LOSS=0, RATE RENEG=0>
>><RETRAINS REQ=1, RETRAINS DET=0>
>><TX FINAL RATE=14400, RX FINAL RATE=14400>
>><PROTOCOL NEGOTIATION=LAPM>
>><EC FRAME SIZE=80>
>><EC LINK TIMEOUTS=0>
>><EC LINK NAKS=0>
>><COMPRESSION NEGOTIATION=V42BIS>
>><COMPRESSION DICTIONARY SIZE=800>
>><TX FLOW CONTROL=2>
>><RX FLOW CONTROL=2>
>><TX CHARS SENT FROM DTE=2624>
>><RX CHARS SENT TO DTE=16BB4>
>><TX CHARS LOST=0>
>><RX CHARS LOST=0>
>><TX FRAME COUNT=9F>
>><RX FRAME COUNT=33D>
>><TX FRAME ERROR COUNT=D>
>><RX FRAME ERROR COUNT=12>
>><TERMINATION CAUSE=Retrain failed>
>><LSD Vdd=0, Power Bits=0>
>><V8BIS FLEX VERSION=0, V8BIS DSP VERSION=47>
>><RATE RENEG REQ=0, RATE RENEG DET=0>
>><HIGH PASS FILTER ENABLED=0>
>><ROBBED BIT PATTERN=0>
>><DIGITAL PAD DETECTED=0, DIGITAL LOSS ESTIMATE=0>
>><Cnt1=0, Det1=1, Res1=0>
>><EQM=7FF7, TRAINING EQM SUM=48FF0>
>><DIB ERROR COUNTERS=0, 0, 0, 0, 0, 0, 0, 0>
>><RETRAIN/HDLC RESET=0>
>>
>>OK