[hcflinux] framing error on startup

[tomshortall]

I noticed the thread from last week.
I have been having a similar problem.
I am using the  conextant HCF winmodem
The modem works just fine with a ppp link to my isp, but the driver keeps 
routing messages relating to messed up frames to the console.When there is 
a download of any size going on the screen rapidly becomes covered in gunk. 
The phone line here is noisy - I get reported connection speeds of 16Kb/s 
under windows.

Example - from /var/log/debug :

Apr 18 12:35:53 jupiter kernel: 1222504.288: >>>EC_ERROR: Frame 69 is out 
of order. (68)1222504.288: >>>EC_ERROR: build_rej_p0

Marc said to send him the capture from AT#UG so it is at the bottom of this 
mail.

I want to get the damn thing off my console  - switching to gui cures it 
but that's not the point.

How Can I stop the messages from going to the console?

I am using syslog-ng and the killer is I can't see in the .conf file 
anywhere that could be telling it to send this crap straight to the console.
There was only one line in syslog-ng.conf concerning  logging to console 
(for emergencies) and I disabled that earlier on (line 2 of this extract) :
 >syslog-ng.conf extract<

log { source(src); filter(f_messages); destination(messages); };
#log { source(src); filter(f_emergency); destination(console); };
log { source(src); filter(f_cnews); destination(xconsole); };
log { source(src); filter(f_cother); destination(xconsole); };

 >end extract<

Any ideas relating to syslog-ng or to the modem driver?
There is no mention of turning off/on debugging in the modem driver docs.
Debian 2.2r5
kernel 2.2.16
pppd 2.4.? - yeah I updated it
syslog 2.5.16 - update from 2.4.0 earlier on to no avail
hcflinmodem package 0.9beta

Thanks
tom

MINICOM CAPTURE
----------------------------------------------------------------------------------------------------------------------------

#ug
<#UG VERSION=1>
<UNIMODEM VERSION=10>
<CALL SETUP RESULT=Detected Data Answer Tone>
<MULTIMEDIA MODE=Data Only>
<DTE-DCE MODE=Async data>
<V.8 CM octet string="">
<V.8 JM octet string="">
<RX SIG POWER DB=26, TX SIG POWER DB=15, S/N RATIO DB=18>
<NORMALIZED MEAN SQUARED ERROR=0>
<NEAR ECHO LOSS=0>
<FAR ECHO LOSS=0>
<FAR ECHO DELAY=0>
<ROUND TRIP DELAY=0>
<V.34 INFO bit map =0>
<TX MOD=V.34, TX SYMBOL RATE=3429, TX CARRIER FREQ=0>
<RX MOD=V.34, RX SYMBOL RATE=3429, RX CARRIER FREQ=0>
<TX FIRST DATA RATE=14400, RX FIRST DATA RATE=14400>
<CARRIER LOSS=0, RATE RENEG=0>
<RETRAINS REQ=1, RETRAINS DET=0>
<TX FINAL RATE=14400, RX FINAL RATE=14400>
<PROTOCOL NEGOTIATION=LAPM>
<EC FRAME SIZE=80>
<EC LINK TIMEOUTS=0>
<EC LINK NAKS=0>
<COMPRESSION NEGOTIATION=V42BIS>
<COMPRESSION DICTIONARY SIZE=800>
<TX FLOW CONTROL=2>
<RX FLOW CONTROL=2>
<TX CHARS SENT FROM DTE=261E>
<RX CHARS SENT TO DTE=16600>
<TX CHARS LOST=0>
<RX CHARS LOST=0>
<TX FRAME COUNT=9F>
<RX FRAME COUNT=33D>
<TX FRAME ERROR COUNT=D>
<RX FRAME ERROR COUNT=12>
<TERMINATION CAUSE=Retrain failed>
<LSD Vdd=0, Power Bits=0>
<V8BIS FLEX VERSION=0, V8BIS DSP VERSION=47>
<RATE RENEG REQ=0, RATE RENEG DET=0>
<HIGH PASS FILTER ENABLED=0>
<ROBBED BIT PATTERN=0>
<DIGITAL PAD DETECTED=0, DIGITAL LOSS ESTIMATE=0>
<Cnt1=0, Det1=1, Res1=0>
<EQM=7FF7, TRAINING EQM SUM=48FF0>
<DIB ERROR COUNTERS=0, 0, 0, 0, 0, 0, 0, 0>
<RETRAIN/HDLC RESET=0>

OK
at#ug
<#UG VERSION=1>
<UNIMODEM VERSION=10>
<CALL SETUP RESULT=Detected Data Answer Tone>
<MULTIMEDIA MODE=Data Only>
<DTE-DCE MODE=Async data>
<V.8 CM octet string="">
<V.8 JM octet string="">
<RX SIG POWER DB=26, TX SIG POWER DB=15, S/N RATIO DB=18>
<NORMALIZED MEAN SQUARED ERROR=0>
<NEAR ECHO LOSS=0>
<FAR ECHO LOSS=0>
<FAR ECHO DELAY=0>
<ROUND TRIP DELAY=0>
<V.34 INFO bit map =0>
<TX MOD=V.34, TX SYMBOL RATE=3429, TX CARRIER FREQ=0>
<RX MOD=V.34, RX SYMBOL RATE=3429, RX CARRIER FREQ=0>
<TX FIRST DATA RATE=14400, RX FIRST DATA RATE=14400>
<CARRIER LOSS=0, RATE RENEG=0>
<RETRAINS REQ=1, RETRAINS DET=0>
<TX FINAL RATE=14400, RX FINAL RATE=14400>
<PROTOCOL NEGOTIATION=LAPM>
<EC FRAME SIZE=80>
<EC LINK TIMEOUTS=0>
<EC LINK NAKS=0>
<COMPRESSION NEGOTIATION=V42BIS>
<COMPRESSION DICTIONARY SIZE=800>
<TX FLOW CONTROL=2>
<RX FLOW CONTROL=2>
<TX CHARS SENT FROM DTE=2624>
<RX CHARS SENT TO DTE=16BB4>
<TX CHARS LOST=0>
<RX CHARS LOST=0>
<TX FRAME COUNT=9F>
<RX FRAME COUNT=33D>
<TX FRAME ERROR COUNT=D>
<RX FRAME ERROR COUNT=12>
<TERMINATION CAUSE=Retrain failed>
<LSD Vdd=0, Power Bits=0>
<V8BIS FLEX VERSION=0, V8BIS DSP VERSION=47>
<RATE RENEG REQ=0, RATE RENEG DET=0>
<HIGH PASS FILTER ENABLED=0>
<ROBBED BIT PATTERN=0>
<DIGITAL PAD DETECTED=0, DIGITAL LOSS ESTIMATE=0>
<Cnt1=0, Det1=1, Res1=0>
<EQM=7FF7, TRAINING EQM SUM=48FF0>
<DIB ERROR COUNTERS=0, 0, 0, 0, 0, 0, 0, 0>
<RETRAIN/HDLC RESET=0>

OK