[hsflinux] Problems with Conextant-Ambit SoftK56 on Sony laptop !
Uli
Uli-Rompel-Ad at gmx.de
Sun May 11 00:01:05 EDT 2003
hello,
sory for my bad english.
i have a sony vaio PCG-GRX616MP laptop and i am trying to install my
modem on a
debian (knoppix) linux system (version 2.4.19-xfs).
my modem is the
Conextant-Ambit SoftK56 Data,Fax ICH Modem 8086:2486
but all i do ... the modem does not work. i read the articles in this
forum and found many
persons, who habe the same problem as i. but no tip worked.
i did the following steps:
at first i downloaded the
hsflinmodem-5.03.27lnxbeta03042700.tar driver from the homepage
www.linuxant.com
(HSF (softmodem) driver)
then i installed the driver with 'make install' and then with
'hsfconfig'.
after that i changed the county to GERMANY with 'hsfconfig --country'.
then i started 'modconf'.
i changed into 'misc' and loaded the module 'hsfengine'.
then i loaded the module 'hsfserial'.
after that the following lines are written in /var/log/syslog:
May 10 19:02:48 laptop insmod: Warning: loading
/lib/modules/2.4.19-xfs/misc/hsfich.o will taint the kernel: non-GPL
license - Copyright (C) 1996-2001 Conexant Systems Inc. All Rights
Reserved.
May 10 19:02:48 laptop insmod: See
http://www.tux.org/lkml/#export-tainted for information about tainted
modules
May 10 19:02:48 laptop insmod: Module hsfich loaded, with warnings
May 10 19:02:49 laptop kernel: PCI: No IRQ known for interrupt pin B of
device 00:1f.6. Please try using pci=biosirq.
May 10 19:02:49 laptop kernel: PCI: Setting latency timer of device
00:1f.6 to 64
May 10 19:02:49 laptop kernel: LinuxHookInterrupt: request for IRQ 0
failed
May 10 19:02:49 laptop kernel: hsf_request_port: open failed
then i run a few commands:
root at laptop:~# lspci
00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host
Bridge (rev 04)
00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge
(rev 04)
00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02)
00:1d.1 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #2) (rev 02)
00:1d.2 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #3) (rev 02)
00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 42)
00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02)
00:1f.3 SMBus: Intel Corp. 82801CA/CAM SMBus (rev 02)
00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97 Audio
(rev 02)
00:1f.6 Modem: Intel Corp. 82801CA/CAM AC'97 Modem (rev 02)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility
M7 LW
02:05.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev a8)
02:05.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev a8)
02:05.2 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller
02:08.0 Ethernet controller: Intel Corp. 82801CAM (ICH3) Chipset
Ethernet Controller (rev 42)
root at laptop:~# lsmod
Module Size Used by Tainted: P
hsfich 95340 0 (autoclean)
hsfserial 22484 0 (unused)
hsfengine 869324 0 [hsfserial]
hsfosspec 22204 0 [hsfich hsfserial hsfengine]
lvm-mod 60768 0 (autoclean)
ds 6472 4
rtc 6908 0
apm 9644 1
yenta_socket 8704 2
pcmcia_core 37536 0 [ds yenta_socket]
usb-uhci 21612 0 (unused)
usbmouse 1752 0 (unused)
hid 19172 0 (unused)
usbcore 56736 1 [usb-uhci usbmouse hid]
mousedev 3832 1
input 3200 0 [usbmouse hid mousedev]
serial 51908 0
i810_rng 2660 0 (unused)
...
i could find the follwing lines in /etc/modules.conf
### update-modules: start processing /etc/modutils/hsf
alias /dev/ttySHSF0 hsfserial
alias char-major-240 hsfserial
alias /dev/ttyCUA* hsfserial
alias char-major-241 hsfserial
alias /dev/modem hsfserial
options hsfserial serialmajor=240 calloutmajor=241
### update-modules: end processing /etc/modutils/hsf
the link /dev/modem is there and the file ttySHSF0, too:
root at laptop:/dev# ls -l ttyS*
crw-rw-rw- 1 root dialout 4, 64 May 10 18:11 ttyS0
crw-rw-rw- 1 root dialout 4, 65 May 14 2002 ttyS1
crw-rw-rw- 1 root dialout 4, 66 Apr 15 2001 ttyS2
crw-rw-rw- 1 root dialout 4, 67 Apr 15 2001 ttyS3
crw-rw-rw- 1 root root 240, 64 May 10 17:56 ttySHSF0
now i configured the ppp conection 'provider' with pppconfig
In pppconfig i used the link /dev/modem
after running 'pon' the following lines are written in /var/log/syslog
May 10 19:14:00 laptop kernel: CSLIP: code copyright 1989 Regents of the
University of California
May 10 19:14:00 laptop kernel: PPP generic driver version 2.4.2
May 10 19:14:00 laptop pppd[2543]: pppd 2.4.1 started by root, uid 0
May 10 19:14:01 laptop chat[2544]: Can't get terminal parameters:
Input/output error
May 10 19:14:01 laptop pppd[2543]: Connect script failed
May 10 19:14:02 laptop pppd[2543]: Exit.
now i read in an article, that i should try the boot command
'pci=biosirq' on the lili promt.
but that did not work. still the same problems.
then i tried the boot command 'pci=acpi'. still the same problems.
here is my lili.conf (without the two boot commands):
boot=/dev/hda3
vga=791
prompt
timeout=50
append = "hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi
hdh=scsi apm=power-off noapic"
image=/boot/vmlinuz-2.4.19-xfs
label=knoppix
root=/dev/hda3
read-only
#other=/dev/hda1
# label=freedos
# table=/dev/hda
here the data from the modem with the listmodem programm:
Build Number : 2600
=====================================================================
= RESULT OF MODEM QUERY =
=====================================================================
NUMBER OF MODEMS FOUND = 1
MODEM #1:
PCI CONFIGURATION INFORMATION READ:
VENDOR ID : 8086
DEVICE ID : 2486
SUBVENDOR ID : 104D
SUBDEVICE ID : 80FA
REVISION ID : 02
DEDUCED INFORMATION:
VENDOR NAME : UNKNOWN
DEVICE NAME : UNKNOWN
SUBVENDOR NAME : UNKNOWN
MODEM TYPE : HSF
WINXP INBUILD SUPPORT : NO
what can i do to solve these problems? what can i do to bring the modem
installed correctly?
can anyone help me ?
thanks !
More information about the hsflinux
mailing list