[hsflinux] Pulse dialing problem (Asus A2800S laptop)

[Denis Isayev]

    I have Mandrake 10.1 with kernel 2.6.8.1-12mdk and  
<http://www.linuxant.com/drivers/hsf/full/archive/hsfmodem-7.18.00.03full/hsfmodem-7.18.00.03full_k2.6.8.1_12mdk-1mdk.i586.rpm.zip>hsfmodem-7.18.00.03full_k2.6.8.1_12mdk-1mdk.i586.rpm 
driver installed on my laptop. Driver installation and hsfconfig 
successfuly completed. But when I'm dialing my ISP with ATDP it seems 
that modem dials only first digit of the number and then do nothing 
several minutes until my telephone operator respond with busy tones. If 
I use ATDT command, modem can generate tones for all digits of the 
number, but this is not useful since I have pulse thelephone line :(
    There was a similar problem in  this list 
(http://www.linuxant.com/pipermail/hsflinux/2003q4/001276.html) but 
unfortunately without an answer.
    My modem device identified by scanModem as
-----------------------------------------------------------------------------------
PCIBUS=00:02.6

Providing detail for device at PCI_bus 00:02.6
  with vendor-ID:device-ID
            ----:----
Class 0703: 1039:7013   Modem: Silicon Integrated Systems [SiS] AC'97 
Modem Controller (rev a0) (prog-if 00 [Generic])
  SubSystem 1043:1816   Asustek Computer, Inc.: Unknown device 1816
        Flags: bus master, medium devsel, latency 32, IRQ 11
        I/O ports at b400 [size=256]
        I/O ports at b000 [size=128]

                  -----PCI_IDs-------                    --CompilerVer-
    Feature List:  Primary  Subsystem Distr  KernelVer   kernel default  CPU
 ./scanModem test 1039:7013 1043:1816 mandrake 2.6.8.1-12mdk 3.4.1 
3.4.1    i686

  The soft modem Subsystem operates under a controller
   1039:7013  SIS 630
 capable of supporting under Linux AT LEAST modem Subsystem chips from 
manufacturers:
        Pctel
        AgereSystems
        Conexant
        Intel
        Smartlink
 The modem has a Conexant codec: CXT
 and there is support for the modem controller: 1039:7013  SIS 630
----------------------------------------------------------------------------------- 


lspci -v shows the following info:

Modem: Silicon Integrated Systems [SiS] AC'97 Modem Controller (rev a0) 
(prog-if 00 [Generic])
        Subsystem: Asustek Computer, Inc.: Unknown device 1816
        Flags: bus master, medium devsel, latency 32, IRQ 11
        I/O ports at b400 [size=256]
        I/O ports at b000 [size=128]
        Capabilities: [48] Power Management version 2

-----------------------------------------------------------------------------------

My wvdial.conf is

[Dialer Defaults]
Modem = /dev/ttySHSF0
Baud = 57600
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ISDN = 0
Modem Type = Analog Modem
Phone = 7893727
Username = xxxxx
Password = yyyyy


[Dialer zebra]
Dial Command = ATDP

[Dialer beelineUSB]
Modem = /dev/ttyUSB0
Baud = 115200
Init2 = AT+CGDCONT=1,"IP","internet.beeline.ru"
Carrier Check = no
Phone = *99***1#
Username = beeline
Password = beeline

-----------------------------------------------------------------------------------

lastcallstatus is
-----------------------------------------------------------------------------------
<#UG VERSION=3>
<DRIVER VERSION=hsfmodem-7.18.00.03full>
<CALL SETUP RESULT=Detected No Recognizable Tone>
<MULTIMEDIA MODE=Data Only>
<DTE-DCE MODE=Async data>
<V.8 CM="">
<V.8 JM="">
<RX SIG PWR DB=0, TX SIG PWR DB=0, S/N RATIO DB=0>
<RTD=0>
<TX MOD=Unknown, TX SYMBOL RATE=0, TX CARRIER FREQ=0>
<RX MOD=Unknown, RX SYMBOL RATE=0, RX CARRIER FREQ=0>
<TX FIRST RATE=0, RX FIRST RATE=0>
<CARRIER LOSS=0, RATE RENEG=0>
<RETRAINS REQ=0, RETRAINS DET=0>
<TX FINAL RATE=0, RX FINAL RATE=0>
<PROTOCOL=None>
<EC FRAME SIZE=0>
<EC LINK TIMEOUTS=0>
<EC LINK NAKS=0>
<COMPRESSION=None>
<COMPRESSION DICTIONARY SIZE=0>
<TX FLOW CONTROL=0>
<RX FLOW CONTROL=0>
<TX CHARS SENT FROM DTE=2>
<RX CHARS SENT TO DTE=13>
<TX CHARS LOST=0>
<RX CHARS LOST=0>
<TX FRAME COUNT=0>
<RX FRAME COUNT=0>
<TX FRAME ERROR COUNT=0>
<RX FRAME ERROR COUNT=0>
<TERMINATION CAUSE=Key abort>
<CALL WAITING EVENT COUNT=0>
<LSD Vdd=0, Power Bits=0>
<V8BIS DSP VER=0>
<RATE RENEG REQ=0, RATE RENEG DET=0>
<RBS=0, AltRBS=0>
<DIG PAD DET=0, DIG LOSS EST=0, IMD RATIO=0, SPEED DROP=0>
<HS CNT=0, Det1=0, Res1=0, LAPM=0>
<EQM=0, TRAINING EQM=0>
<HandShake Time=0.0>

<DIB ERROR COUNTERS=0, 0, 0, 0, 0, 0, 0, 0>
-------------------------------------------------------------------------------------------------

lsmod | grep hsf shows:
-------------------------------------------------------------------------------------------------
hsfusbcd2              56600  0
hsfmc97sis             47536  0
hsfmc97ati             45712  0
hsfmc97ali             52052  0
hsfmc97via             49080  0
hsfmc97ich             50832  0
hsfpcibasic2           56336  0
hsfserial              18916  7 
hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2
hsfengine            1299348  1 hsfserial
hsfosspec              81700  12 
hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2,hsfserial,hsfengine
hsfsoar                57248  7 
hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2
usbcore               103172  10 
hsfusbcd2,hsfosspec,pl2303,usbserial,usbmouse,usbhid,ehci-hcd,ohci-hcd
----------------------------------------------------------------------------------------------------

Please let me know I you need any additional info about  this problem.

Thanks,
    Denis.