[hsflinux] HSF modem picks up line but Does Not Dial

[Linuxant support (Jonathan)]

Hi,

everything seems fine in the dump you have provided, as far as the modem 
driver is concerned.

When you use 'AT &F X1' with "Init1", please make sure that you don't 
use "Init2" as these settings might override some settings if 'AT &F X1'.

Finally, you are using a 2.4 kernels and there is a lot of known IRQ 
issues with these kernels and an IRQ problem could be the source of the 
problem you have described. You could try with a 2.6 kernel to see if 
there is a difference.

Regards,


Jonathan
Technical specialist / Linuxant
www.linuxant.com
support at linuxant.com



Daniele (Mastro) wrote:
>> hi.. im not the one here...
>> but i have the same problem:
>>
>> Country: Italy.. (i've setted it writing "ITALY" when asked in hsfconfig
>> --country)
>>
>> the modem is: Communication Controller: Rockwell International HSF 56k
>> Data/Fax Modem code (127a:2013)
>> PCI
>>
>> i've installed the latest version of the driver.. no problem during install
>>
>> than i tried with both ppp and wvdial, same problem: pick up the line (i
>> can ear
>>
>> here my wvdial.conf
>>
>> [Dialer Default]
>> Carrier Check = no  # Tried both with or without this
>> Init1 = ATZ         # i've tried AT &F X1, too
>> Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>> Modem Type = Analog Modem
>> ISDN = 0
>> New PPPD = yes
>> Phone = .... # here my phone numbar
>> Modem = /dev/modem   # symlink to /dev/ttySHF0
>> Username = ...
>> Password = ...
>> Baud = 115200
>>
>> here the wvdial log without comment:
>>
>> ATZ
>> OK
>>
>> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>> OK
>>
>> ATDTXXXXXXXXX     # the X are the numbar
>>
>> the line go down after a while..... and it retry with the same result
>>
>>
>> (can you or any other reply to me? i've not a subscription)
> 
> 
> sorry.. i forgotten the hsfdiag.txt...
> 
> here... hope you can help me..
> i noticed this in dmesg:
> 
> ttySHSF0 at I/O 0xde00 (irq = 9) is a Conexant HSF softmodem
> (PCI-127a:2013-1436:2113)
> usb.c: registered new driver hsfusbcd2
> usb.c: deregistering driver hsfusbcd2
> PCI: Found IRQ 9 for device 00:0a.0
> ttySHSF0 at I/O 0xde00 (irq = 9) is a Conexant HSF softmodem
> (PCI-127a:2013-1436:2113)
> usb.c: registered new driver hsfusbcd2
> usb.c: deregistering driver hsfusbcd2
> PCI: Found IRQ 9 for device 00:0a.0
> ttySHSF0 at I/O 0xde00 (irq = 9) is a Conexant HSF softmodem
> (PCI-127a:2013-1436:2113)
> usb.c: registered new driver hsfusbcd2
> usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 10 ret -32
> usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 4 ret -32
> 
> 
> thank you again,
> goodbye
> 
> _______________________________________________
> hsflinux mailing list
> hsflinux at lists.linuxant.com
> https://www.linuxant.com/mailman/listinfo/hsflinux