[hsflinux] Pulse dialing problem (Asus A2800S laptop)

Tue May 3 20:35:24 EDT 2005

Thank you for quick response!

    I've issued hsfconfig --country RUSSIA and after this checked region 
with ATI9 command:
ATI9
RUSSIA
OK
Also I've changed Init1 in wvdial.conf to AT &F
and commented Init2 string

But the result in both cases still the same: modem sends only first 
digit of the number

Denis.

Linuxant support (Jonathan) wrote:

> Hi,
>
> please make sure that the right country is selected with the 
> 'hsfconfig --country' command in a root shell. You could also try with 
> the 'AT &F' as the only init. string.
>
> Regards,
>
>
> Jonathan
> Technical specialist / Linuxant
> www.linuxant.com
> support at linuxant.com
>
>
>
> Denis Isayev wrote:
>
>>    I have Mandrake 10.1 with kernel 2.6.8.1-12mdk and  
>> <http://www.linuxant.com/drivers/hsf/full/archive/hsfmodem-7.18.00.03full/hsfmodem-7.18.00.03full_k2.6.8.1_12mdk-1mdk.i586.rpm.zip>hsfmodem-7.18.00.03full_k2.6.8.1_12mdk-1mdk.i586.rpm 
>> driver installed on my laptop. Driver installation and hsfconfig 
>> successfuly completed. But when I'm dialing my ISP with ATDP it seems 
>> that modem dials only first digit of the number and then do nothing 
>> several minutes until my telephone operator respond with busy tones. 
>> If I use ATDT command, modem can generate tones for all digits of the 
>> number, but this is not useful since I have pulse thelephone line :(
>>    There was a similar problem in  this list 
>> (http://www.linuxant.com/pipermail/hsflinux/2003q4/001276.html) but 
>> unfortunately without an answer.
>>    My modem device identified by scanModem as
>> ----------------------------------------------------------------------------------- 
>>
>> PCIBUS=00:02.6
>>
>> Providing detail for device at PCI_bus 00:02.6
>>  with vendor-ID:device-ID
>>            ----:----
>> Class 0703: 1039:7013   Modem: Silicon Integrated Systems [SiS] AC'97 
>> Modem Controller (rev a0) (prog-if 00 [Generic])
>>  SubSystem 1043:1816   Asustek Computer, Inc.: Unknown device 1816
>>        Flags: bus master, medium devsel, latency 32, IRQ 11
>>        I/O ports at b400 [size=256]
>>        I/O ports at b000 [size=128]
>>
>>                  -----PCI_IDs-------                    --CompilerVer-
>>    Feature List:  Primary  Subsystem Distr  KernelVer   kernel 
>> default  CPU
>> ./scanModem test 1039:7013 1043:1816 mandrake 2.6.8.1-12mdk 3.4.1 
>> 3.4.1    i686
>>
>>  The soft modem Subsystem operates under a controller
>>   1039:7013  SIS 630
>> capable of supporting under Linux AT LEAST modem Subsystem chips from 
>> manufacturers:
>>        Pctel
>>        AgereSystems
>>        Conexant
>>        Intel
>>        Smartlink
>> The modem has a Conexant codec: CXT
>> and there is support for the modem controller: 1039:7013  SIS 630
>> ----------------------------------------------------------------------------------- 
>>
>>
>> lspci -v shows the following info:
>>
>> Modem: Silicon Integrated Systems [SiS] AC'97 Modem Controller (rev 
>> a0) (prog-if 00 [Generic])
>>        Subsystem: Asustek Computer, Inc.: Unknown device 1816
>>        Flags: bus master, medium devsel, latency 32, IRQ 11
>>        I/O ports at b400 [size=256]
>>        I/O ports at b000 [size=128]
>>        Capabilities: [48] Power Management version 2
>>
>> ----------------------------------------------------------------------------------- 
>>
>>
>> My wvdial.conf is
>>
>> [Dialer Defaults]
>> Modem = /dev/ttySHSF0
>> Baud = 57600
>> Init1 = ATZ
>> Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>> ISDN = 0
>> Modem Type = Analog Modem
>> Phone = 7893727
>> Username = xxxxx
>> Password = yyyyy
>>
>>
>> [Dialer zebra]
>> Dial Command = ATDP
>>
>> [Dialer beelineUSB]
>> Modem = /dev/ttyUSB0
>> Baud = 115200
>> Init2 = AT+CGDCONT=1,"IP","internet.beeline.ru"
>> Carrier Check = no
>> Phone = *99***1#
>> Username = beeline
>> Password = beeline
>>
>> ----------------------------------------------------------------------------------- 
>>
>>
>> lastcallstatus is
>> ----------------------------------------------------------------------------------- 
>>
>> <#UG VERSION=3>
>> <DRIVER VERSION=hsfmodem-7.18.00.03full>
>> <CALL SETUP RESULT=Detected No Recognizable Tone>
>> <MULTIMEDIA MODE=Data Only>
>> <DTE-DCE MODE=Async data>
>> <V.8 CM="">
>> <V.8 JM="">
>> <RX SIG PWR DB=0, TX SIG PWR DB=0, S/N RATIO DB=0>
>> <RTD=0>
>> <TX MOD=Unknown, TX SYMBOL RATE=0, TX CARRIER FREQ=0>
>> <RX MOD=Unknown, RX SYMBOL RATE=0, RX CARRIER FREQ=0>
>> <TX FIRST RATE=0, RX FIRST RATE=0>
>> <CARRIER LOSS=0, RATE RENEG=0>
>> <RETRAINS REQ=0, RETRAINS DET=0>
>> <TX FINAL RATE=0, RX FINAL RATE=0>
>> <PROTOCOL=None>
>> <EC FRAME SIZE=0>
>> <EC LINK TIMEOUTS=0>
>> <EC LINK NAKS=0>
>> <COMPRESSION=None>
>> <COMPRESSION DICTIONARY SIZE=0>
>> <TX FLOW CONTROL=0>
>> <RX FLOW CONTROL=0>
>> <TX CHARS SENT FROM DTE=2>
>> <RX CHARS SENT TO DTE=13>
>> <TX CHARS LOST=0>
>> <RX CHARS LOST=0>
>> <TX FRAME COUNT=0>
>> <RX FRAME COUNT=0>
>> <TX FRAME ERROR COUNT=0>
>> <RX FRAME ERROR COUNT=0>
>> <TERMINATION CAUSE=Key abort>
>> <CALL WAITING EVENT COUNT=0>
>> <LSD Vdd=0, Power Bits=0>
>> <V8BIS DSP VER=0>
>> <RATE RENEG REQ=0, RATE RENEG DET=0>
>> <RBS=0, AltRBS=0>
>> <DIG PAD DET=0, DIG LOSS EST=0, IMD RATIO=0, SPEED DROP=0>
>> <HS CNT=0, Det1=0, Res1=0, LAPM=0>
>> <EQM=0, TRAINING EQM=0>
>> <HandShake Time=0.0>
>>
>> <DIB ERROR COUNTERS=0, 0, 0, 0, 0, 0, 0, 0>
>> ------------------------------------------------------------------------------------------------- 
>>
>>
>> lsmod | grep hsf shows:
>> ------------------------------------------------------------------------------------------------- 
>>
>> hsfusbcd2              56600  0
>> hsfmc97sis             47536  0
>> hsfmc97ati             45712  0
>> hsfmc97ali             52052  0
>> hsfmc97via             49080  0
>> hsfmc97ich             50832  0
>> hsfpcibasic2           56336  0
>> hsfserial              18916  7 
>> hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2 
>>
>> hsfengine            1299348  1 hsfserial
>> hsfosspec              81700  12 
>> hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2,hsfserial,hsfengine 
>>
>> hsfsoar                57248  7 
>> hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2 
>>
>> usbcore               103172  10 
>> hsfusbcd2,hsfosspec,pl2303,usbserial,usbmouse,usbhid,ehci-hcd,ohci-hcd
>> ---------------------------------------------------------------------------------------------------- 
>>
>>
>> Please let me know I you need any additional info about  this problem.
>>
>> Thanks,
>>    Denis.
>>
>> _______________________________________________
>> hsflinux mailing list
>> hsflinux at lists.linuxant.com
>> https://www.linuxant.com/mailman/listinfo/hsflinux
>