[hsflinux] Pulse dialing problem (Asus A2800S laptop)
Linuxant support (Jonathan)
support at linuxant.com
Tue May 3 16:28:24 EDT 2005
Hi,
please test under Windows XP on the same machine to see if you have a
similar problem. You should also send at support at linuxant.com the output
of 'dumpdiag'. Type the following in a root shell:
---
hsfconfig --dumpdiag
---
Just send us the generated file located in /tmp ('hsfdiag.txt').
It'll help us solve the problem.
Regards,
Jonathan
Technical specialist / Linuxant
www.linuxant.com
support at linuxant.com
Denis Isayev wrote:
> Thank you for quick response!
> I've issued hsfconfig --country RUSSIA and after this checked
> region with ATI9 command:
> ATI9
> RUSSIA
> OK
> Also I've changed Init1 in wvdial.conf to AT &F
> and commented Init2 string
>
> But the result in both cases still the same: modem sends only first
> digit of the number
>
> Denis.
>
> Linuxant support (Jonathan) wrote:
>
>> Hi,
>>
>> please make sure that the right country is selected with the
>> 'hsfconfig --country' command in a root shell. You could also try with
>> the 'AT &F' as the only init. string.
>>
>> Regards,
>>
>>
>> Jonathan
>> Technical specialist / Linuxant
>> www.linuxant.com
>> support at linuxant.com
>>
>>
>>
>> Denis Isayev wrote:
>>
>>> I have Mandrake 10.1 with kernel 2.6.8.1-12mdk and
>>> <http://www.linuxant.com/drivers/hsf/full/archive/hsfmodem-7.18.00.03full/hsfmodem-7.18.00.03full_k2.6.8.1_12mdk-1mdk.i586.rpm.zip>hsfmodem-7.18.00.03full_k2.6.8.1_12mdk-1mdk.i586.rpm
>>> driver installed on my laptop. Driver installation and hsfconfig
>>> successfuly completed. But when I'm dialing my ISP with ATDP it seems
>>> that modem dials only first digit of the number and then do nothing
>>> several minutes until my telephone operator respond with busy tones.
>>> If I use ATDT command, modem can generate tones for all digits of the
>>> number, but this is not useful since I have pulse thelephone line :(
>>> There was a similar problem in this list
>>> (http://www.linuxant.com/pipermail/hsflinux/2003q4/001276.html) but
>>> unfortunately without an answer.
>>> My modem device identified by scanModem as
>>> -----------------------------------------------------------------------------------
>>>
>>> PCIBUS=00:02.6
>>>
>>> Providing detail for device at PCI_bus 00:02.6
>>> with vendor-ID:device-ID
>>> ----:----
>>> Class 0703: 1039:7013 Modem: Silicon Integrated Systems [SiS] AC'97
>>> Modem Controller (rev a0) (prog-if 00 [Generic])
>>> SubSystem 1043:1816 Asustek Computer, Inc.: Unknown device 1816
>>> Flags: bus master, medium devsel, latency 32, IRQ 11
>>> I/O ports at b400 [size=256]
>>> I/O ports at b000 [size=128]
>>>
>>> -----PCI_IDs------- --CompilerVer-
>>> Feature List: Primary Subsystem Distr KernelVer kernel
>>> default CPU
>>> ./scanModem test 1039:7013 1043:1816 mandrake 2.6.8.1-12mdk 3.4.1
>>> 3.4.1 i686
>>>
>>> The soft modem Subsystem operates under a controller
>>> 1039:7013 SIS 630
>>> capable of supporting under Linux AT LEAST modem Subsystem chips from
>>> manufacturers:
>>> Pctel
>>> AgereSystems
>>> Conexant
>>> Intel
>>> Smartlink
>>> The modem has a Conexant codec: CXT
>>> and there is support for the modem controller: 1039:7013 SIS 630
>>> -----------------------------------------------------------------------------------
>>>
>>>
>>> lspci -v shows the following info:
>>>
>>> Modem: Silicon Integrated Systems [SiS] AC'97 Modem Controller (rev
>>> a0) (prog-if 00 [Generic])
>>> Subsystem: Asustek Computer, Inc.: Unknown device 1816
>>> Flags: bus master, medium devsel, latency 32, IRQ 11
>>> I/O ports at b400 [size=256]
>>> I/O ports at b000 [size=128]
>>> Capabilities: [48] Power Management version 2
>>>
>>> -----------------------------------------------------------------------------------
>>>
>>>
>>> My wvdial.conf is
>>>
>>> [Dialer Defaults]
>>> Modem = /dev/ttySHSF0
>>> Baud = 57600
>>> Init1 = ATZ
>>> Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>>> ISDN = 0
>>> Modem Type = Analog Modem
>>> Phone = 7893727
>>> Username = xxxxx
>>> Password = yyyyy
>>>
>>>
>>> [Dialer zebra]
>>> Dial Command = ATDP
>>>
>>> [Dialer beelineUSB]
>>> Modem = /dev/ttyUSB0
>>> Baud = 115200
>>> Init2 = AT+CGDCONT=1,"IP","internet.beeline.ru"
>>> Carrier Check = no
>>> Phone = *99***1#
>>> Username = beeline
>>> Password = beeline
>>>
>>> -----------------------------------------------------------------------------------
>>>
>>>
>>> lastcallstatus is
>>> -----------------------------------------------------------------------------------
>>>
>>> <#UG VERSION=3>
>>> <DRIVER VERSION=hsfmodem-7.18.00.03full>
>>> <CALL SETUP RESULT=Detected No Recognizable Tone>
>>> <MULTIMEDIA MODE=Data Only>
>>> <DTE-DCE MODE=Async data>
>>> <V.8 CM="">
>>> <V.8 JM="">
>>> <RX SIG PWR DB=0, TX SIG PWR DB=0, S/N RATIO DB=0>
>>> <RTD=0>
>>> <TX MOD=Unknown, TX SYMBOL RATE=0, TX CARRIER FREQ=0>
>>> <RX MOD=Unknown, RX SYMBOL RATE=0, RX CARRIER FREQ=0>
>>> <TX FIRST RATE=0, RX FIRST RATE=0>
>>> <CARRIER LOSS=0, RATE RENEG=0>
>>> <RETRAINS REQ=0, RETRAINS DET=0>
>>> <TX FINAL RATE=0, RX FINAL RATE=0>
>>> <PROTOCOL=None>
>>> <EC FRAME SIZE=0>
>>> <EC LINK TIMEOUTS=0>
>>> <EC LINK NAKS=0>
>>> <COMPRESSION=None>
>>> <COMPRESSION DICTIONARY SIZE=0>
>>> <TX FLOW CONTROL=0>
>>> <RX FLOW CONTROL=0>
>>> <TX CHARS SENT FROM DTE=2>
>>> <RX CHARS SENT TO DTE=13>
>>> <TX CHARS LOST=0>
>>> <RX CHARS LOST=0>
>>> <TX FRAME COUNT=0>
>>> <RX FRAME COUNT=0>
>>> <TX FRAME ERROR COUNT=0>
>>> <RX FRAME ERROR COUNT=0>
>>> <TERMINATION CAUSE=Key abort>
>>> <CALL WAITING EVENT COUNT=0>
>>> <LSD Vdd=0, Power Bits=0>
>>> <V8BIS DSP VER=0>
>>> <RATE RENEG REQ=0, RATE RENEG DET=0>
>>> <RBS=0, AltRBS=0>
>>> <DIG PAD DET=0, DIG LOSS EST=0, IMD RATIO=0, SPEED DROP=0>
>>> <HS CNT=0, Det1=0, Res1=0, LAPM=0>
>>> <EQM=0, TRAINING EQM=0>
>>> <HandShake Time=0.0>
>>>
>>> <DIB ERROR COUNTERS=0, 0, 0, 0, 0, 0, 0, 0>
>>> -------------------------------------------------------------------------------------------------
>>>
>>>
>>> lsmod | grep hsf shows:
>>> -------------------------------------------------------------------------------------------------
>>>
>>> hsfusbcd2 56600 0
>>> hsfmc97sis 47536 0
>>> hsfmc97ati 45712 0
>>> hsfmc97ali 52052 0
>>> hsfmc97via 49080 0
>>> hsfmc97ich 50832 0
>>> hsfpcibasic2 56336 0
>>> hsfserial 18916 7
>>> hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2
>>>
>>> hsfengine 1299348 1 hsfserial
>>> hsfosspec 81700 12
>>> hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2,hsfserial,hsfengine
>>>
>>> hsfsoar 57248 7
>>> hsfusbcd2,hsfmc97sis,hsfmc97ati,hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2
>>>
>>> usbcore 103172 10
>>> hsfusbcd2,hsfosspec,pl2303,usbserial,usbmouse,usbhid,ehci-hcd,ohci-hcd
>>> ----------------------------------------------------------------------------------------------------
>>>
>>>
>>> Please let me know I you need any additional info about this problem.
>>>
>>> Thanks,
>>> Denis.
>>>
>>> _______________________________________________
>>> hsflinux mailing list
>>> hsflinux at lists.linuxant.com
>>> https://www.linuxant.com/mailman/listinfo/hsflinux
>>
>>
>
> _______________________________________________
> hsflinux mailing list
> hsflinux at lists.linuxant.com
> https://www.linuxant.com/mailman/listinfo/hsflinux
More information about the hsflinux
mailing list