[driverloader] Success with driverloader and Dell True Mobil 1300
But...
Bob Talbot
talbotrobert at sbcglobal.net
Tue Sep 6 03:02:09 EDT 2005
Hi
Well it seems a manual shell command as root ## ifup wlan0 activates the card.
Now I am conected to ping the router and use the internet and Local net.
I am happy with the results.
Just two questions.
1 .. What do I do to activate ifup wlan0 on Boot? I find no ifcfg-wlan0 script.
Where is it do I write one, if so an example please
2.. What utilities can I use to see Signal power Graphically and to pick up another router on which I am allowed and in Range of as I only entered One ESSID.
Or is this Automatic?
My INFO AS OF IFDOWN wlan0 & IFUP wlan0
the xxx and iii in my ips are for my security on the mail list.
ifdown wlan0
wlan0 device: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 02)
linux:/home/bobby # ifup wlan0
wlan0 device: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 02)
wlan0 warning: using NO encryption
Starting DHCP Client Daemon on wlan0... . . . . . IP/Netmask: 192.168.xxx.iii / 255.255.255.0
ERROR: Warning: Could not set up default route via interface
Command ip route replace to default via 198.168.xxx.xxx returned:
. RTNETLINK answers: Network is unreachable
Configuration line: default 198.168.xxx.xxx - -
This needs NOT to be AN ERROR if you set up multiple interfaces.
See man 5 routes how to avoid this warning.
*********************************************
My INFO BEFORE IFDOWN wlan0 & IFUP wlan0
linux:/home/bobby # iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11-DS ESSID:"USR8022" Nickname:"unknown"
Mode:Managed Frequency:2.462 GHz Access Point: 00:C0:49:A6:68:1B
Bit Rate=11 Mb/s Tx-Power=25 dBm
RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=3/94 Signal level=-78 dBm Noise level=-154 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:353 Missed beacon:0
eth1 no wireless extensions.
sit0 no wireless extensions.
linux:/home/bobby # dmesg
Linux version 2.6.11.4-21.9-default (geeko at buildhost) (gcc version 3.3.5 2005011
7 (prerelease) (SUSE Linux)) #1 Fri Aug 19 11:58:59 UTC 2005
SECTION of dmesg that applies to Wan card
++++++++++++++++++++++++++++++++++++++++++
eth0: Broadcom 4400 10/100BaseT Ethernet 00:0b:db:9d:0f:dd
driverloader: no version for "struct_module" found: kernel tainted.
driverloader: module license 'see LICENSE file; Copyright (c)2003-2004 Linuxant
inc.' taints kernel.
driverloader: stack=8192/60/0 REGPARM
usbcore: registered new driver driverloader
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x820-0x8ff: excluding 0x8e0-0x8e7
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
driverloader: bcmwl5.sys: 0xf9326000..0xf9380180 entry = f9331dd2 (pbase = 0x100
00)
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 11 (level, low) -> IRQ 11
0000:02:02.0: cache line size not set; forcing 32
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0xa00-0xaff: clean.
wlan0: New link status: Disconnected (0002)
wlan0: WPA, AES, TKIP, WEP128, WEP64 supported
wlan0: at 0000:02:02.0 (MAC address 00:90:4B:28:79:6F) ready
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Linux Tulip driver version 1.1.13-NAPI (May 11, 2002)
PCI: Enabling device 0000:03:00.0 (0000 -> 0003)
ACPI: PCI interrupt 0000:03:00.0[A] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:03:00.0 to 64
tulip0: MII transceiver #1 config 3100 status 7849 advertising 05e1.
eth1: ADMtek Comet rev 17 at 00014000, 00:0F:B5:45:D3:AE, IRQ 11.
NET: Registered protocol family 17
st: Version 20041025, fixed bufsize 32768, s/g segs 256
wlan0: New link status: Connected (0001)
Non-volatile memory driver v1.2
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.linuxant.com/pipermail/driverloader/attachments/20050906/cecee868/attachment.htm
More information about the driverloader
mailing list